Conductivity Measurement in Life Sciences Industry Clean-in-Place (CIP) Applications
Clean-in-Place (CIP) Liquid Analysis Solutions for the Pharmaceutical Industry
Sanitary Conductivity Sensor Provides Accurate Measurement
Cleaning process equipment in place in the pharmaceutical industry is done periodically to remove residue from previous batches and to sanitize the equipment. The cleaning process requires a series of flushes with detergents, acid solutions and water. Conductivity measurement is used to monitor the progression of the cleaning cycles and to determine when each cycle is complete as the cleaning solutions are more conductive than the water used for flushing and rinsing. Conductivity sensors in these applications need to have a sanitary design to make sure they do not trap residue that could decay or harbor microorganisms. The Rosemount™ 245 Sanitary Flow-Through Toroidal Conductivity Sensor is a great solution for pharmaceutical manufacturing as toroidal sensor technology seldom requires cleaning and features smooth surfaces.
Klik om verder te gaan met lezen Sanitary Conductivity Sensor Provides Accurate Measurement
Product Solutions
This product is now obsolete. Relevant documents and drawings are listed below.
Contact your local Emerson representative for your measurement needs.
Contact your local Emerson representative for your measurement needs.
The Rosemount 1058 Dual Channel Transmitter provides confident liquid analysis measurement in a wide range of industrial, municipal and commercial applications. It is a 4-wire powered device that provides multi-parameter liquid analysis for digital and analog sensors, including inputs from pH/ORP sensors, ISE, flow, current, conductivity sensors (contacting and toroidal), turbidity sensors and amperometric sensors (dissolved oxygen, chlorine and ozone).
- Supports continuous measurement of liquid analysis inputs from one or two sensors.
- Each sensor channel is independently configurable to support a wide selection of digital or analog liquid analysis sensors including pH sensors, ORP sensors, conductivity sensors, dissolved oxygen sensors, chlorine senors, turbidity sensors and more.
- IP66 / Type 4X rated engineered polymer enclosure with universal mounting options provides confident and easy installation indoors or outdoors.
Enclosure Rating
Type 4X, IP66
Dimensions
Overall 160 x 157 x 140 mm (6.3 x 6.2 x 5.5 in); Cutout 138.4 x 138.4 mm (5.45 x 5.45 in)
Weight
3 lb (1.5 kg)
The Rosemount 1066 Single Channel Transmitter supports continuous measurement of one liquid analytical input - pH sensor, conductivity sensor, chlorine sensor, dissolved oxygen sensor or ozone sensor. The design supports easy internal access and wiring connections. The large display gives excellent visibility for live measurements and displayed parameters. Conveniently, live process values are always displayed during programming and calibration routines.
- Fast and easy installation using Quick Start programming
- Intrinsically Safe FM, CSA, and ATEX/IECEx Hazardous Location Approvals
- Visibility of process parameters by utilizing HART® or FOUNDATION™ Fieldbus digital communications
Power Supply
Supply voltage at the transmitter terminals should be at least 12.7Vdc. Power supply voltage should cover the voltage drop on the cable plus the external load resistor required for HART® communications (250 Ω)
Weight
R2 lbs/3 lbs (1 kg/1.5 kg)
Communication Protocol
HART™ Communications & diagnostics: PV, SV, TV, and 4V assignable, temperature
The Rosemount 400 Contacting Conductivity Sensor, with integral cable, accurately measures electrolytic conductivity in a broad range of applications from high purity water to clean cooling water. The Rosemount 400 conductivity sensor is ideal for use in clean, non-corrosive liquid having less than 20,000 µS/cm.
- Factory-measured cell constant ensures out-of-the-box accuracy and no initial calibration requirements
- Available in cell constants of 0.01, 0.1, and 1.0/cm
- Conductivity sensor designed for direct screw-in insertion into process piping using a front facing 3/4 inch MNPT fitting
Design
Cell constants: 0.01, 0.1, and 1.0/cm
Vacuum: At 1.6 in. Hg (5.2 kPa) air leakage is less than 0.005 SCFM (0.00014 m3/min)
Vacuum: At 1.6 in. Hg (5.2 kPa) air leakage is less than 0.005 SCFM (0.00014 m3/min)
Dimensions
Cable length (Model 400 only): 10 ft (3.1 m) standard; 50 ft (15.2 m) optional
Materials of Construction
Wetted Materials: Electrodes - titanium; Body - 316 stainless steel; Insulator - PEEK; O-Rings - EPDM
